DFM Review Skill
Purpose
The DFM Review skill provides capabilities for systematic design for manufacturing review and optimization, enabling cost-effective and producible mechanical designs.
Capabilities
- Manufacturability assessment
- Process selection guidance
- Tooling feasibility analysis
- Cost driver identification
- Design modification recommendations
- Tolerance and surface finish review
- Material availability assessment
- Supplier capability consideration
Usage Guidelines
DFM Principles
Core DFM Guidelines
1. Minimize part count
2. Use standard components
3. Design for ease of fabrication
4. Design for ease of assembly
5. Design for ease of service
6. Consider process capabilities
7. Minimize secondary operations
Process-Specific Guidelines
| Process | Key DFM Considerations | |---------|----------------------| | Machining | Access, fixturing, tool reach | | Casting | Draft, wall thickness, gates/risers | | Injection molding | Draft, undercuts, sink marks | | Sheet metal | Bend radius, hole-to-edge, grain | | Welding | Access, joint design, distortion | | Assembly | Part orientation, fastener access |
Machining DFM
Feature Guidelines
Holes:
- Standard drill sizes preferred
- L/D ratio < 5 for drills
- Flat bottoms require end mill
- Provide drill point clearance
Pockets:
- Corner radius = tool radius
- Max depth < 4x tool diameter
- Provide tool access
Threads:
- Standard thread sizes
- Depth 1.5-2x diameter sufficient
- Provide thread relief
Wall thickness:
- Minimum 1-2 mm for steel
- Consider deflection during machining
Tolerance Capability
| Dimension Type | Typical Capability | |----------------|-------------------| | Linear (milling) | +/- 0.025 mm | | Linear (turning) | +/- 0.013 mm | | Hole diameter | +/- 0.013 mm | | Surface finish | Ra 1.6-3.2 um | | Flatness | 0.025 mm/100 mm |
Casting DFM
Design Guidelines
Draft angles:
- External: 1-3 degrees minimum
- Internal: 2-5 degrees
- Deep pockets: increase draft
Wall thickness:
- Minimum: 3-5 mm (sand casting)
- Minimum: 2-3 mm (die casting)
- Uniform thickness preferred
- Gradual transitions
Radii:
- Internal corners: R > 3 mm
- External corners: R > 1 mm
- Avoid sharp transitions
Shrinkage Allowance
| Material | Shrinkage % | |----------|-------------| | Aluminum | 1.2-1.5 | | Steel | 1.5-2.0 | | Cast iron | 0.8-1.2 | | Bronze | 1.0-1.5 |
Injection Molding DFM
Design Guidelines
Wall thickness:
- Uniform 1.5-4 mm
- Transitions < 25% thickness change
- Avoid thick sections (sink marks)
Draft:
- 0.5-1 degree per side minimum
- Textured surfaces: add 1 degree per 0.025 mm depth
Ribs:
- Thickness: 50-75% of wall
- Height: < 3x wall thickness
- Spacing: > 2x wall thickness
Bosses:
- Wall: 50-75% of base wall
- Height: < 2x diameter
- Add gussets for strength
Sheet Metal DFM
Bend Guidelines
Minimum bend radius:
- Soft materials: 0.5x thickness
- Hard materials: 1-2x thickness
- With grain: smaller radius OK
- Against grain: larger radius
Minimum flange:
- Flange > 4x thickness
- Flange > 3 mm practical minimum
Hole-to-bend:
- Distance > 2x thickness + bend radius
- Prevents hole distortion
Punching Guidelines
Minimum hole size:
- Round: 1x material thickness
- Square/rectangle: 0.8x thickness
Minimum edge distance:
- 2x material thickness minimum
- Prevents edge deformation
Minimum hole spacing:
- 2x material thickness minimum
Cost Drivers
Cost Analysis Framework
Manufacturing cost components:
1. Material cost
- Raw material
- Scrap/waste
- Special materials
2. Labor cost
- Setup time
- Run time
- Inspection time
3. Equipment cost
- Machine time
- Tooling amortization
4. Overhead
- Facility
- Support functions
Cost Reduction Opportunities
| Area | Opportunity | |------|-------------| | Material | Standard grades, near-net-shape | | Features | Eliminate unnecessary features | | Tolerances | Relax to process capability | | Finish | Specify only where needed | | Operations | Combine or eliminate steps | | Assembly | Reduce part count, use snap fits |
Tolerance Review
Tolerance Stacking
Before specifying tight tolerances:
1. Verify functional requirement
2. Check assembly chain
3. Confirm process capability
4. Consider inspection cost
5. Evaluate statistical tolerance
Cost Impact
| Tolerance Class | Relative Cost | |-----------------|---------------| | Standard (+/- 0.5 mm) | 1x | | Precision (+/- 0.1 mm) | 2-3x | | Close (+/- 0.025 mm) | 5-10x | | Very close (+/- 0.01 mm) | 10-20x |
Process Integration
- ME-005: Design for Manufacturing (DFM) Review
Input Schema
{
"design_data": {
"cad_model": "file reference",
"drawings": "array of references",
"material": "string"
},
"manufacturing_context": {
"target_process": "machining|casting|molding|sheet_metal|additive",
"production_volume": "prototype|low|medium|high",
"target_cost": "number (optional)"
},
"supplier_constraints": {
"preferred_suppliers": "array",
"equipment_limitations": "array"
}
}
Output Schema
{
"dfm_assessment": {
"overall_rating": "good|acceptable|needs_improvement",
"manufacturability_score": "number (1-10)"
},
"issues": [
{
"feature": "string",
"issue": "string",
"severity": "critical|major|minor",
"recommendation": "string",
"cost_impact": "string"
}
],
"cost_analysis": {
"material_cost": "number",
"labor_cost": "number",
"tooling_cost": "number",
"total_unit_cost": "number"
},
"improvement_opportunities": [
{
"change": "string",
"cost_savings": "number or percentage",
"effort": "low|medium|high"
}
],
"process_recommendation": {
"primary_process": "string",
"secondary_operations": "array",
"special_requirements": "array"
}
}
Best Practices
- Involve manufacturing early in design
- Understand process capabilities
- Challenge tight tolerances
- Consider total cost, not just piece cost
- Design for the target volume
- Document DFM decisions and rationale
Integration Points
- Connects with CAD Modeling for design review
- Feeds into Process Planning for manufacturing
- Supports Trade Study for process selection
- Integrates with Cost estimation