Embedded Systems & IoT Skill

Embedded Systems & IoT

Microcontroller Platforms

| Platform | Best For | Language | IDE | |----------|----------|----------|-----| | ESP32 | WiFi/BLE IoT devices | C/C++, MicroPython | PlatformIO, Arduino IDE | | STM32 | Industrial, real-time | C/C++ | STM32CubeIDE, PlatformIO | | Arduino | Prototyping, learning | C++ (Arduino) | Arduino IDE, PlatformIO | | Raspberry Pi Pico | RP2040, dual-core | C/C++, MicroPython | Thonny, VS Code | | nRF52 | BLE-focused IoT | C, Zephyr | nRF Connect SDK |

Firmware Patterns

GPIO & Peripherals

// ESP-IDF GPIO example
gpio_config_t io_conf = {
    .pin_bit_mask = (1ULL << GPIO_NUM_2),
    .mode = GPIO_MODE_OUTPUT,
    .pull_up_en = GPIO_PULLUP_DISABLE,
    .pull_down_en = GPIO_PULLDOWN_DISABLE,
    .intr_type = GPIO_INTR_DISABLE,
};
gpio_config(&io_conf);
gpio_set_level(GPIO_NUM_2, 1);

I2C Communication

// Read sensor via I2C
i2c_cmd_handle_t cmd = i2c_cmd_link_create();
i2c_master_start(cmd);
i2c_master_write_byte(cmd, (SENSOR_ADDR << 1) | I2C_MASTER_WRITE, true);
i2c_master_write_byte(cmd, REG_TEMP, true);
i2c_master_start(cmd);
i2c_master_write_byte(cmd, (SENSOR_ADDR << 1) | I2C_MASTER_READ, true);
i2c_master_read(cmd, data, 2, I2C_MASTER_LAST_NACK);
i2c_master_stop(cmd);
i2c_master_cmd_begin(I2C_NUM_0, cmd, pdMS_TO_TICKS(1000));
i2c_cmd_link_delete(cmd);

RTOS (FreeRTOS)

// Task creation
void sensor_task(void *pvParameters) {
    while (1) {
        float temp = read_temperature();
        xQueueSend(data_queue, &temp, portMAX_DELAY);
        vTaskDelay(pdMS_TO_TICKS(1000));
    }
}
xTaskCreate(sensor_task, "sensor", 4096, NULL, 5, NULL);

// Mutex for shared resources
SemaphoreHandle_t spi_mutex = xSemaphoreCreateMutex();
if (xSemaphoreTake(spi_mutex, pdMS_TO_TICKS(100)) == pdTRUE) {
    spi_transfer(data);
    xSemaphoreGive(spi_mutex);
}

IoT Protocols

MQTT

// ESP-IDF MQTT client
esp_mqtt_client_config_t mqtt_cfg = {
    .broker.address.uri = "mqtt://broker.hivemq.com",
};
esp_mqtt_client_handle_t client = esp_mqtt_client_init(&mqtt_cfg);
esp_mqtt_client_start(client);
esp_mqtt_client_publish(client, "/sensors/temp", "23.5", 0, 1, 0);

Key IoT Protocols

| Protocol | Transport | Use Case | |----------|-----------|----------| | MQTT | TCP/TLS | Pub/sub messaging, telemetry | | CoAP | UDP/DTLS | Constrained devices, REST-like | | BLE | Radio | Short-range, low power | | LoRaWAN | Radio | Long-range, low data rate | | Matter | IP | Smart home interoperability |

Best Practices

Power management: Deep sleep modes, wake-on-interrupt, duty cycling
Watchdog timers: Always enable, reset periodically, catch firmware hangs
OTA updates: Dual partition scheme, rollback on boot failure, signature verification
Memory: Static allocation preferred, avoid heap fragmentation, use memory pools
Testing: Hardware-in-the-loop (HIL), mock hardware interfaces for unit tests

Agent Skills: Embedded Systems & IoT

Install this agent skill to your local

Skill Files